• High performance in compact package. Electric and battery powered models for powering tools and cylinders upto 25 ton.
• Portable power source for hydraulic cylinders and tools.
• Permanent magnet motor starts easily under load, even with reduced voltage conditions.
• Pumps for 3000 psi and 5000 psi operating pressures available.
• Battery-operated models have 8 foot power cord with alligator clips to connect to any 12 volt battery.
• Optional rechargeable battery pack with shoulder strap for maximum portability.
• Pump typically delivers 15 minutes of continuous operation at 10000 psi on a single battery.
• Pump can be operated in any position.
• 24 volt hand and foot switches available for all AC powered pump models.
• High-impact housing with flame-retardant construction.
• Base mounting holes for fixed installations.

• For maintenance and construction applications.
• For use with single-acting or double-acting cylinders at operating pressures to 10000 psi.
• For intermittent duty; starts under full load.
• Equipped with 1/2 hp, 3450 rpm, single-phase, thermal protected induction motor; 10 ft. remote control cord (PE172S has 25 ft. cord).
• Low amperage draw; small generators and low amperage circuits can be used as power source.
• Extremely quiet with noise level ranging from 67 - 81dBA.

Typical oil delivery flow is given. Actual flow will vary with field conditions.
The remote motor control switch on 220V, 50 cycle PE17 series pumps is 24 volt.
Usable oil is calculated with the oil fill at the recommended level of 11/2" below reservoir cover plate.
Control switch on PE17 series wired with line voltage.
The dBa is measured at 3 ft. distance all sides.

• Vanguard Jr. pumps provide two-speed high performance in a light-weight, compact package.
• Gauge port provided on pump. Metal reservoir on all models.
• Equipped with a 1/2 hp, 110/115 volt, 60/50 Hz single phase motor that starts under load, even at reduced voltage.
• Low amperage draw permits use with smaller generators and low amperage circuits.
• All pumps have a 10 foot remote control (except PE183C which has 25 foot remote control).
• CSA rated for intermittent duty. High noise level of 85-90 dBA.

Typical oil delivery flow is given. Actual flow will vary with field conditions.
Measured at 3 ft. distance, all sides.

• Totally enclosed, fan cooled induction motor: 1 hp, 1,725 rpm, 60 Hz, single phase. Thermal overload protection.
• Remote control, with 10 foot cord is standard on pumps with solenoid valves. Manual valve pumps have "Stop", "Start" and "Run /Off / Pulse" switches.
• Pump controls are moisture and dust resistant.
• Motor drip cover with carrying handles and lifting lug.
• Low noise level of dBA @ 10,000 psi.
• In the event of electrical interruption, pump shuts off and will not start up until operator presses the pump start button.
• 24 volt controls circuits on units with remote controls provide additional user / operator safety.

   Shipping weight with manual valve; add 14 lbs. for pump with solenoid valve.

• Two-speed pumps have the same low pressure and high pressure flows from both valves.
• Flows and pressures of each pump are independent.
• Delivers 300 cu. in./min. of oil @ 100 psi and 25 cu. in./min. @ 10,000 psi from each pump.
• 1-1/2 hp, 110/115 volt, 60 Hz induction motor, 10 foot remote control and 5 gallon steel reservoir.
• Models available for operating single-acting or double-acting cylinders.
• Each power unit contains two separate pumps and two separate valves allowing operator to control multiple processes with one power unti.
• Both pumps on each power unit are equipped with an externally adjustable pressure relief valve.
• Not recommended for frequent starting and stopping.

• Deliver a powerful punch to operate single-acting or double acting cylinders.
• Integral roll cage protects pump from abuse.
• 1 hp, single phase, permanent magnet motor.
• Start under full load even when voltage is reduced to 50% of nominal rating.
• High performance to weight ratio.
• Quiet operation: 82 dBA at 10000 psi and 87 dBA at 0 psi. CSA rated for intermittent duty.
• Remote controls and/or solenoid valves feature 24 volt controls.

• Two-speed high performance pump.
• For use with single- or double-acting cylinders at operating pressures to 10,000 psi.
• Equipped with a 1 1/2 hp, 3,450 rpm single-phase, 60 Hz thermal protected induction motor that starts under fullload. Noise level of 77-81 dBA.
• All equipped with a 10 foot remote control except PE462S which has a 25 foot remote control.
• 24 volt control circuit on all units with remote control for user/operator safety.
• CSA rated for intermittent duty.

Measured at 3 ft. distance, all sides.
Requires 20 amp circuit.
Typical oil delivery flow is given. Actual flow will vary with field conditions.
Available with 220 V., 50 Hz motor (to order, place suffix “50-220” behind pump order number). Specify voltage when ordering.
The remote motor control switch on PE46 series pumps is 24 volt.

• 1 1/8 hp, 12000 rpm, 110/115 volt, 50/60 Hz universal motor; draws 25 amps at full load, starts at reduced voltage.
• 10 foot remote motor control except PE552S which has a 25 foot remote motor and valve control.
• True unloading valve achieves greater pump efficiency, allowing higher flows at maximum pressure.
• Reservoirs available in sizes up to 10 gallons.
• Light weight and portable. Best weight to performance ratio of all Power Team pumps.
• “Assemble to Order” System: There are times when a custom pump is required. Power Team’s “Assemble to Order” system allows you to choose from a wide range of pre-engineered, off-the-shelf components to build a customized pump to fit specific requirements. By selecting standard components you get a “customized” pump without “customized” prices. All pumps come fully assembled, less oil and ready for work.

Noise level reading (dBA) measured at a 3 ft. distance, all sides.
Amp draw at 10000 psi, 230 Volts 50/60 Hz is 15 Amps.
Pumps available with 230 volt, 60/50 Hz motors. Specify voltage when ordering.
To order PE55 series pumps with CSA approval, add “–C” to the Order No.
Control switch wired with line voltage. All remotes are 10 ft. long except for PE552S which is 25 ft. long.

• For operating single- or double-acting cylinders. Two speed, high performance pumps are ideal for heavy duty, extended cycle operation at operating pressures to 10,000 psi.
• Metal shroud keeps dirt and moisture out of motor and electrical components.
• Electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption.
• Internal relief valve limits pressure to 10,000 psi. External relief valve is adjustable from 1,000 to 10,000 psi.
• Pumps operate below maximum OSHA noise limitation (74-76 dBA).
• Start and operate under full load, even with voltage reduced 10%.

Measured at 3 ft distance, all sides.
Total weight with oil and 3-way solenoid valve. Subtract 10 lbs to obtain weight of pump with manual valve.
K 1/2-20 UNF for 2" dia, swivel casters, order (4) No 10494.
PQ60 series also available in 115V, 60 Hz or 220V, 50 Hz. Please specify when ordering. Example: for 60 Hz order PQ603-115; for 50 Hz order PQ603-50-220.

• Start and operate under full load, even with voltage reduced 10%.
• Electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption.
• Internal relief valve limits pressure to 10,000 psi. External relief valve is adjustable from 1,000 to 10,000 psi.
• Pump prewired at factory with a 3hp, 460 volt, 60 Hz. 3 Phase motor. Other electrical configurations are available.
• 24 volt control circuits on units with remote controls for added user/operator safety.
• 3 hp (3 phase) motor with thermal overload protection. Motor starter and heater element supplied as standard equipment; no hidden charges.
• Metal shroud keeps dirt and moisture out of motor and electrical components.
• Pumps operate below maximum OSHA noise limitation.

Measured at 3 ft distance, all sides.
Total weight with oil and 3-way solenoid valve. Subtract 10 lbs. to obtain weight of pump with manual valve.
K 1/2-20 UNF for 2" dia swivel casters, order (4) No. 10494
PQ120 series also available in 230V 60 Hz or 220/380V 50 Hz. Please specify when ordering. Example: for 60 Hz order PQ1204S-230; for 50 Hz. order PQ1204S-50-220 or PQ1204S-50-380. PQ120 Series also available in 575V 60 Hz. Consult the factory.

• 5/8 hp universal electric motor (50/60 cycle)
• Two-stage pump for rapid ram advance
• Operational under low-line voltage conditions
• Optional operating pressures available; consult Power Team for details
• Designed for use with spring-returned remote tools
• High-pressure safety relief valve
• Remote hand control with 10-foot cord
• Carrying handle
• Factory filled oil reservoir
• Pressure matched quick-coupler supplied
• Optional carrying case
• Two-stage pumping system
• Unique, intermittent duty pump,
• Piston-type high-pressure pump supercharged by a low-pressure pump.

• Two-stage pump for rapid advance.
• High-pressure safety relief valve.
• Protective roll cage.

• A logical choice at work sites where electricity or compressed air are unavailable.
• For single- or double-acting cylinders at operating pressures to 10,000 psi.
• All gasoline engine/hydraulic pumps feature "Posi-Check" valve to guard against pressure loss when vale is shifted from "advance" to "hold".
• PG303 and PG304 powered by a 2-cycle, 2 hp Tecumseh engine giving it the lowest weight to horsepower ratio of all gasoline driven pumps. Has an aluminum reservoir with 375 cu. in. of usable oil.
• PG553 and PG554 , 6 hp Intek "Diamond Edge" 4-cycle, by Briggs & Stratton. 5 gallon reservoir.

• Two-speed high performance pumps ideal for construction, structure moving and rigging applications.
• A logical choice at work sites where electricity or compressed air are unavailable.
• For single- or double-acting cylinders at operating pressures to 10,000 psi.
• All gasoline engine/hydraulic pumps feature "Posi-Check" valve to guard against pressure loss when valve is shifted from "advance" to "hold".
• PG1200 Series pumps powered by a Honda 4-cycle, 5.5 hp engine with automatic decompression and electronic ignition. Deliver over 1/2 gallon (130 cu. in.) of oil per minute at 10,000 psi.
• A 5 gallon reservoir means adequate capacity for multi-cylinder applications. Dual element air cleaner protects engine from dusty environments.
• Heavy duty "roll cage" provides pick-up points for lifting. Horizontal bars on PG1203, PG1204 and PG1204S protect unit, provide hand holds for carrying.
• Rubber anti-skid insulation on bottom of reservoir resists skidding and dampens vibration. PG1200M-4 and PG1200M-4D include a pump cart with 12" wheels.
• Adjustable external pressure regulator.