Electric/Gasoline/Battery Pumps

• High performance in compact package. Electric and battery powered models for powering tools and cylinders upto 25 ton.
• Portable power source for hydraulic cylinders and tools.
• Permanent magnet motor starts easily under load, even with reduced voltage conditions.
• Pumps for 3000 psi and 5000 psi operating pressures available.
• Battery-operated models have 8 foot power cord with alligator clips to connect to any 12 volt battery.
• Optional rechargeable battery pack with shoulder strap for maximum portability.
• Pump typically delivers 15 minutes of continuous operation at 10000 psi on a single battery.
• Pump can be operated in any position.
• 24 volt hand and foot switches ...

• For maintenance and construction applications.
• For use with single-acting or double-acting cylinders at operating pressures to 10000 psi.
• For intermittent duty; starts under full load.
• Equipped with 1/2 hp, 3450 rpm, single-phase, thermal protected induction motor; 10 ft. remote control cord (PE172S has 25 ft. cord).
• Low amperage draw; small generators and low amperage circuits can be used as power source.
• Extremely quiet with noise level ranging from 67 - 81dBA.

• Vanguard Jr. pumps provide two-speed high performance in a light-weight, compact package.
• Gauge port provided on pump. Metal reservoir on all models.
• Equipped with a 1/2 hp, 110/115 volt, 60/50 Hz single phase motor that starts under load, even at reduced voltage.
• Low amperage draw permits use with smaller generators and low amperage circuits.
• All pumps have a 10 foot remote control (except PE183C which has 25 foot remote control).
• CSA rated for intermittent duty. High noise level of 85-90 dBA.

• Totally enclosed, fan cooled induction motor: 1 hp, 1,725 rpm, 60 Hz, single phase. Thermal overload protection.
• Remote control, with 10 foot cord is standard on pumps with solenoid valves. Manual valve pumps have "Stop", "Start" and "Run /Off / Pulse" switches.
• Pump controls are moisture and dust resistant.
• Motor drip cover with carrying handles and lifting lug.
• Low noise level of dBA @ 10,000 psi.
• In the event of electrical interruption, pump shuts off and will not start up until operator presses the pump start button.
• 24 volt controls circuits on units with remote controls provide additional user / operator safety.

   Shipping weight with ...

• Two-speed pumps have the same low pressure and high pressure flows from both valves.
• Flows and pressures of each pump are independent.
• Delivers 300 cu. in./min. of oil @ 100 psi and 25 cu. in./min. @ 10,000 psi from each pump.
• 1-1/2 hp, 110/115 volt, 60 Hz induction motor, 10 foot remote control and 5 gallon steel reservoir.
• Models available for operating single-acting or double-acting cylinders.
• Each power unit contains two separate pumps and two separate valves allowing operator to control multiple processes with one power unti.
• Both pumps on each power unit are equipped with an externally adjustable pressure relief valve.
• Not recommended for frequent ...

• Deliver a powerful punch to operate single-acting or double acting cylinders.
• Integral roll cage protects pump from abuse.
• 1 hp, single phase, permanent magnet motor.
• Start under full load even when voltage is reduced to 50% of nominal rating.
• High performance to weight ratio.
• Quiet operation: 82 dBA at 10000 psi and 87 dBA at 0 psi. CSA rated for intermittent duty.
• Remote controls and/or solenoid valves feature 24 volt controls.

• Two-speed high performance pump.
• For use with single- or double-acting cylinders at operating pressures to 10,000 psi.
• Equipped with a 1 1/2 hp, 3,450 rpm single-phase, 60 Hz thermal protected induction motor that starts under fullload. Noise level of 77-81 dBA.
• All equipped with a 10 foot remote control except PE462S which has a 25 foot remote control.
• 24 volt control circuit on all units with remote control for user/operator safety.
• CSA rated for intermittent duty.

• 1 1/8 hp, 12000 rpm, 110/115 volt, 50/60 Hz universal motor; draws 25 amps at full load, starts at reduced voltage.
• 10 foot remote motor control except PE552S which has a 25 foot remote motor and valve control.
• True unloading valve achieves greater pump efficiency, allowing higher flows at maximum pressure.
• Reservoirs available in sizes up to 10 gallons.
• Light weight and portable. Best weight to performance ratio of all Power Team pumps.
• “Assemble to Order” System: There are times when a custom pump is required. Power Team’s “Assemble to Order” system allows you to choose from a wide range of pre-engineered, off-the-shelf components to build a ...

• For operating single- or double-acting cylinders. Two speed, high performance pumps are ideal for heavy duty, extended cycle operation at operating pressures to 10,000 psi.
• Metal shroud keeps dirt and moisture out of motor and electrical components.
• Electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption.
• Internal relief valve limits pressure to 10,000 psi. External relief valve is adjustable from 1,000 to 10,000 psi.
• Pumps operate below maximum OSHA noise limitation (74-76 dBA).
• Start and operate under full load, even with voltage reduced 10%.

• Start and operate under full load, even with voltage reduced 10%.
• Electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption.
• Internal relief valve limits pressure to 10,000 psi. External relief valve is adjustable from 1,000 to 10,000 psi.
• Pump prewired at factory with a 3hp, 460 volt, 60 Hz. 3 Phase motor. Other electrical configurations are available.
• 24 volt control circuits on units with remote controls for added user/operator safety.
• 3 hp (3 phase) motor with thermal overload protection. Motor starter and heater element supplied as standard equipment; no hidden charges.
• Metal shroud keeps dirt and moisture ...

• 5/8 hp universal electric motor (50/60 cycle)
• Two-stage pump for rapid ram advance
• Operational under low-line voltage conditions
• Optional operating pressures available; consult Power Team for details
• Designed for use with spring-returned remote tools
• High-pressure safety relief valve
• Remote hand control with 10-foot cord
• Carrying handle
• Factory filled oil reservoir
• Pressure matched quick-coupler supplied
• Optional carrying case
• Two-stage pumping system
• Unique, intermittent duty pump,
• Piston-type high-pressure pump supercharged by a low-pressure pump.

• Two-stage pump for rapid advance.
• High-pressure safety relief valve.
• Protective roll cage.

• A logical choice at work sites where electricity or compressed air are unavailable.
• For single- or double-acting cylinders at operating pressures to 10,000 psi.
• All gasoline engine/hydraulic pumps feature "Posi-Check" valve to guard against pressure loss when vale is shifted from "advance" to "hold".
• PG303 and PG304 powered by a 2-cycle, 2 hp Tecumseh engine giving it the lowest weight to horsepower ratio of all gasoline driven pumps. Has an aluminum reservoir with 375 cu. in. of usable oil.
• PG553 and PG554 , 6 hp Intek "Diamond Edge" 4-cycle, by Briggs & Stratton. 5 gallon reservoir.

• Two-speed high performance pumps ideal for construction, structure moving and rigging applications.
• A logical choice at work sites where electricity or compressed air are unavailable.
• For single- or double-acting cylinders at operating pressures to 10,000 psi.
• All gasoline engine/hydraulic pumps feature "Posi-Check" valve to guard against pressure loss when valve is shifted from "advance" to "hold".
• PG1200 Series pumps powered by a Honda 4-cycle, 5.5 hp engine with automatic decompression and electronic ignition. Deliver over 1/2 gallon (130 cu. in.) of oil per minute at 10,000 psi.
• A 5 gallon reservoir means adequate capacity for multi-cylinder applications. Dual element air ...